gigasept®FF (neu)

gigasept® FF (new) is a high-level disinfectant based on succinic acid dialdehyde for manual reprocessing of surgical and sensitive medical instruments.

Our Plus

  • formaldehyde and GDA-free
  • broad microbiological efficacy
  • outstanding material compatibility
  • 14-days standing time

Downloads

Fields of Application

Disinfection of thermolabile and thermostable instruments, e.g. flexible and rigid endoscopes, waterproof ultrasound probes, anaesthesia equipment, breathing masks, instruments etc.

Product Profile


Instructions for use

gigasept® FF (new) is a concentrate and is diluted with cold water to the desired working concentration.

Application example:
1 litre of a 6 % working solution corresponds to 940 ml of water and 60 ml of gigasept® FF (new).
Immerse endoscopes and instruments to be reprocessed in the gigasept® FF (new) solution. Ensure complete covering of the surfaces, also of hollow instruments, and allow them to soak in the solution. After disinfection, thoroughly rinse all instruments, using water of at least drinking water quality, or preferably sterile distilled water or fully deionised water, to completely remove any residues of the solution. Please follow the reprocessing recommendations of the instrument manufacturers.

Standing time:
A standing time of 14 days applies if the working solution is only used for the disinfection of previously cleaned instruments. National regulations may limit the timespan during which the solution can be used.
Apart from the manual treatment of endoscopes and instruments, gigasept® FF (new) is also suitable for semiautomated machines that operate by a cyclic process at room temperature.

Microbiological efficacy

EfficacyConcentrationContact time
bactericidal
EN13727, EN14561, in accordance with VAH
- clean conditions
4 % (40 ml/l)30 min.
bactericidal
EN13727, EN14561, in accordance with VAH
- clean conditions
5 % (50 ml/l)15 min.
bactericidal
EN13727, EN14561, in accordance with VAH
- clean conditions
4 % (20 ml/l)30 min.
tuberculocidal
EN14348, EN14563, in accordance with VAH
- dirty conditions
5 % (50 ml/l)15 min.
tuberculocidal
EN14348, EN14563, in accordance with VAH
- dirty conditions
2 % (40 ml/l)60 min.
tuberculocidal
EN14348, EN14563, in accordance with VAH
- clean conditions
2 % (20 ml/l)60 min.
mycobactericidal
EN14348, EN14563, in accordance with VAH
- clean conditions
3 % (30 ml/l)60 min.
mycobactericidal
EN14348, EN14563, in accordance with VAH
- clean conditions
5 % (50 ml/l)30 min.
mycobactericidal
EN14348, EN14563, in accordance with VAH
- dirty conditions
7 % (70 ml/l)15 min.
yeasticidal
EN13624, EN14562, in accordance with VAH
- clean conditions
2 % (20 ml/l)60 min.
yeasticidal
EN13624, EN14562, in accordance with VAH
- clean conditions
4 % (40 ml/l)30 min.
yeasticidal
EN13624, EN14562, in accordance with VAH
- clean conditions
5 % (50 ml/l)15 min.
yeasticidal
EN13624, EN14562, in accordance with VAH
- clean conditions
5 % (50 ml/l)15 min.
fungicidal
EN13624, EN14562
- clean conditions
6 % (60 ml/l)60 min.
virucidal against enveloped viruses
EN14476, EN17111
- clean conditions
1 % (10 ml/l)15 min.
virucidal against enveloped viruses
in accordance with DVV (German Registered Association for Combating Viral Diseases
1 % (10 ml/l)15 min.
virucidal
in accordance with DVV (German Registered Association for Combating Viral Diseases
8 % (80 ml/l)60 min.
virucidal
EN14476, EN17111
- clean conditions
6 % (60 ml/l)60 min.
Clostridium difficile
EN17126
- clean conditions
6 % (60 ml/l)8 h

Certificates

  • IHO listed
  • VAH certificate

Product data

Composition: 100 g solution contain the following active substances: 93.9 g Reaction product of DMO-THF, ethanol and water.



Chemical-physical data

Flash point:38,5 °C / Method : DIN 51755 Part 1
Form:liquid
Colour:green
Density:ca. 1,01 g/cm3 / 20 °C
Viscosity, dynamic::no data available
pH:6,3 - 6,6 / 100 % / 20 °C

Special advice

Always read the label and product information before useFor professional use only. Any serious incidents related to the product are to be reported to the manufacturer and competent authority.

Material compatibility:
metals, rubber, glass, plastics, flexible endoscopes.

Interactions:
As a general rule, do not mix gigasept® FF (new) with other products. If gigasept® FF (new) comes into contact with application solutions containing amines, there may be precipitation and irreversible discolorations, for example if cleaning agents containing amines are used during precleaning and are not adequately rinsed off.

Storage:
Do not store for long periods above 25 °C. Keep container tightly closed. Protect from frost, heat and sunlight. Store in the original container. Do not use the product after expiry date.

Information for order

ItemDelivery formItem no.
gigasept FF neu 2L5/Cartonson request

These products are not available in every country. For more information please contact our local subsidiary or distributor.

Environmental information

schülke manufactures products economically and with advanced, safe and environmentally friendly production processes while at the same time maintaining out high quality standards.
CE 0297

Privacy Policy

We use analysis methods (e. g. cookies) to measure how often our site is visited and how it is used.
We embed third-party content from other providers (e. g. videos) on our site. We have no influence on further data processing and any tracking by the third party provider.
In this context, we also use service providers in third countries outside the EU that do not have an adequate level of data protection, which harbors the following risks: Access by authorities without informing the data subject, no data subject rights, no legal remedies, loss of control.
With your settings you consent to the processes described above. You can revoke your consent with effect for the future. You can find more information in our privacy policy.