perform®
Active oxygen-based concentrate in powder form for disinfecting and cleaning medical devices and surfaces.
Our Plus
- very good material compatibility
- broad spectrum of activity (limited spectrum of virucidal activity, tuberculocidal, sporicidal (incl. C. difficile))
- active oxygen based
Downloads
Microbiological efficacy
| Efficacy | Concentration | Contact time |
|---|---|---|
| bactericidal EN16615- clean conditions | 0.5 % (5 g/l) | 60 min. |
| bactericidal EN16615- clean conditions | 1 % (10 g/l) | 15 min. |
| bactericidal EN13727- clean conditions | 1 % (10 g/l) | 1 min. |
| bactericidal EN13727- clean conditions | 0.5 % (5 g/l) | 5 min. |
| tuberculocidal EN14348- clean conditions | 2 % (20 g/l) | 60 min. |
| yeasticidal EN13624- clean conditions | 1 % (10 g/l) | 15 min. |
| yeasticidal EN13624- clean conditions | 0.5 % (5 g/l) | 60 min. |
| yeasticidal EN16615- clean conditions | 1 % (10 g/l) | 15 min. |
| yeasticidal EN16615- clean conditions | 0.5 % (5 g/l) | 60 min. |
| fungicidal EN13624, EN13697- dirty conditions | 2 % (20 g/l) | 60 min. |
| virucidal against enveloped viruses EN14476 | 0.5 % (5 g/l) | 5 min. |
| limited spectrum virucidal activity EN14476- clean conditions | 0.5 % (5 g/l) | 5 min. |
| virucidal EN14476- clean conditions | 1 % (10 g/l) | 5 min. |
| Clostridium difficile EN13697- clean conditions | 1 % (10 g/l) | 2 h |
| Clostridium difficile EN17126- clean conditions | 1 % (10 g/l) | 120 min. |
| Application area | Concentration | Contact time |
|---|---|---|
| RKI-listed according to German law (§18 IfSG) - scope AB | 3 % (30 g/l) | 4 h |
Certificates
- IHO listed
- RKI listed
- VAH certificate
Product data
Composition:
100 g solution contains the following active substances: 45 g Pentapotassium-bis-(peroxymonosulphate) bis(sulphate)
Labelling according to Regulation (EC) No. 648/2004:
5 - 15 % anionic surfactants; < 5 % non-ionic surfactants; < 5 % soap and phosphonates, perfumes
100 g solution contains the following active substances: 45 g Pentapotassium-bis-(peroxymonosulphate) bis(sulphate)
Labelling according to Regulation (EC) No. 648/2004:
5 - 15 % anionic surfactants; < 5 % non-ionic surfactants; < 5 % soap and phosphonates, perfumes
Chemical-physical data
Flash point:Not applicable
Form:granular
Color:white
Viscosity, dynamic:Not applicable
pH:ca. 4 / 5 g/l / 20 °C / in water
Special advice
Use disinfectants safely. Always read the label and product information before use.
The working solution may have a bleaching effect on certain very sensitive textile dyestuffs. Wearing protective gloves is advised. Do not store at temperatures above 30°C. Store the container tightly closed and dry. For further information on safe handling and storage conditions, please refer to the safety data sheet. The shelf-life of the opened container can be found on the packaging. Ensure adequate ventilation at the site of application. Do not store bags or boxes above room temperature.
perform® is suitable for disinfecting surfaces and medical devices. As a very well established product with a broad spectrum of activity and high material compatibility, it is used in all hospital areas. Because of its good material compatibility, perform® can also be used on sensitive surfaces such as PMMA. perform is also suitable for disinfecting respiratory and inhalation masks as well as training dummies.
To prepare the working solution, fill the bucket with water, add the product and dissolve. When using the box, the corresponding dosing is carried out according to the dosing table or the box label:
- 1 bag (40 g) to 8 l of water = 0.5% solution
- 2 bags (80 g) to 8 l of water = 1% solution
The prepared working solutions have a lifetime of max. 30 hours (at 20°C) and 4 hours (at 40°C) for guaranteed stability of the active ingredient. The working solution should be replaced earlier in case of heavy contamination. Apply the working solution in the desired concentration to the floor using the 2-step wiping procedure. Wet wipe medical devices and other surfaces. To avoid formation of residues, only minimal residual moisture should remain on the surface after the second wiping step. In the case of immersion disinfection, rinse the products off with water after the exposure time. Because of its good material compatibility, perform® can also be used on sensitive surfaces such as PMMA. Ensure that all visible dirt is removed before disinfection. Ensure complete wetting and maintain the surface moist during the entire exposure time. Clean equipment thoroughly with water. For professional use only. Any serious incidents related to the product are to be reported to the manufacturer and competent authority. Not for final disinfection of semicritical and critical medical devices!
The working solution may have a bleaching effect on certain very sensitive textile dyestuffs. Wearing protective gloves is advised. Do not store at temperatures above 30°C. Store the container tightly closed and dry. For further information on safe handling and storage conditions, please refer to the safety data sheet. The shelf-life of the opened container can be found on the packaging. Ensure adequate ventilation at the site of application. Do not store bags or boxes above room temperature.
Application areas
perform® is suitable for disinfecting surfaces and medical devices. As a very well established product with a broad spectrum of activity and high material compatibility, it is used in all hospital areas. Because of its good material compatibility, perform® can also be used on sensitive surfaces such as PMMA. perform is also suitable for disinfecting respiratory and inhalation masks as well as training dummies.
Instructions for use
To prepare the working solution, fill the bucket with water, add the product and dissolve. When using the box, the corresponding dosing is carried out according to the dosing table or the box label:
- 1 bag (40 g) to 8 l of water = 0.5% solution
- 2 bags (80 g) to 8 l of water = 1% solution
The prepared working solutions have a lifetime of max. 30 hours (at 20°C) and 4 hours (at 40°C) for guaranteed stability of the active ingredient. The working solution should be replaced earlier in case of heavy contamination. Apply the working solution in the desired concentration to the floor using the 2-step wiping procedure. Wet wipe medical devices and other surfaces. To avoid formation of residues, only minimal residual moisture should remain on the surface after the second wiping step. In the case of immersion disinfection, rinse the products off with water after the exposure time. Because of its good material compatibility, perform® can also be used on sensitive surfaces such as PMMA. Ensure that all visible dirt is removed before disinfection. Ensure complete wetting and maintain the surface moist during the entire exposure time. Clean equipment thoroughly with water. For professional use only. Any serious incidents related to the product are to be reported to the manufacturer and competent authority. Not for final disinfection of semicritical and critical medical devices!
Information for order
| Item | Delivery form | Item no. |
|---|---|---|
| perform® tin (900 g) | 4/Carton | on request |
| perform® (60x) 40 g bag | 60/Carton | on request |
| perform® (250x) 40 g bag | 250/Carton | on request |
Environmental information
schülke manufactures products economically and with advanced, safe and environmentally friendly production processes while at the same time maintaining our high quality standards.
0297