terralin® PAA

Active oxygen-based concentrate for disinfecting and cleaning medical devices and surfaces.

Our Plus

  • broad efficacy within very short time
  • very good material compatibility
  • active oxygen based

Downloads

Fields of Application

For targeted use in critical situations, e.g. in case of an outbreak of a nosocomial infection, or to combat critical pathogens such as C. difficile
Special advice

Ensure that all visible dirt is removed before disinfection. Wearing protective gloves is absolutely necessary. Store always upright. Do not seal the container gas tight. Protect from direct sunlight and heat. Keep away from heat and sources of ignition. For further information on safe handling and storage conditions, please refer to the safety data sheet.

Microbiological efficacy

EfficacyConcentrationContact time
bactericidal
EN13727, in accordance with VAH
2 % (20 ml/l)5 min.
tuberculocidal
EN14348
2 % (20 ml/l)5 min.
mycobactericidal
EN14348- clean conditions
2 % (20 ml/l)5 min.
yeasticidal
EN13624, in accordance with VAH
2 % (20 ml/l)5 min.
limited spectrum virucidal activity
EN14476- dirty conditions
1 % (10 ml/l)1 min.
virucidal
EN14476- dirty conditions
2 % (20 ml/l)30 min.
Norovirus
EN14476- dirty conditions
1 % (10 ml/l)5 min.
Poliovirus
EN14476- dirty conditions
2 % (20 ml/l)30 min.
sporicidal
EN14347- dirty conditions
2 % (20 ml/l)5 min.
Clostridium difficile
EN13697
1 % (10 ml/l)15 min.
Clostridium difficile
EN13697- clean conditions
2 % (20 ml/l)5 min.
Application areaConcentrationContact time
RKI-listed according to German law (§18 IfSG) - scope AB
8 % (80 ml/l)60 min.

Certificates

  • ÖGHMP certificate
  • IHO listed
  • RKI listed
  • VAH certificate

Product data

Composition:
component base:
100 g of solution contains: 5 g peracetic acid; other: hydrogenperoxide and acetic acid.
Labelling according to Regulation (EC) No 648/2004:
< 5 % non-ionic surfactants.
component additive:
potassium hydroxide, corrosion inhibitors, phosphates
Labelling according to Regulation (EC) No 648/2004:
< 5 % phosphate



Chemical-physical data
terralin PAA base
density: 1.1 g/cm3, 20°C
Colour: colourless
Flash point: not applicable
Form: liquid
pH value: <1, 20°C (concentrate)


terralin PAA additive
density: approx. 1.2 g/cm3, 20 °C
Colour: yellow
Flash point: not applicable
Form: liquid
pH value: > 13, 20 °C (concentrate)

Special advice

Instructions for use
Use disinfectants safely. Always read the label and product information before use.
To prepare the desired working solution, the required amount of water is first set ready. The double bottle is then completely emptied into the water. In doing so, it must be ensured that the concentrated components are not brought into contact. To obtain a 2% working solution, the entire content of a double bottle is dosed per 4 l of water - - calculated on the basis of the base component. The lifetime of the prepared terralin® PAA working solution is max. 12 hours. The components base and additive always have to be used together! Do not keep container sealed. terralin® PAA is not suitable for chrome plated surfaces and surfaces made of brass or copper. Please refer to manufacturer's instructions regarding the surfaces to be weated and, if necessary, test the material compatibility before application. Do not exceed concentration. The microbiological efficacy and the application properties of peracetic acid are significantly dependent on the pH value of the stock solution. Generally, the recommended concentrations and contact times should not be exceeded with all cleaners and disinfectants, in order to obtain the best possible compatibility of materials. Thus, a peracetic acid solution, as it is also available on the market, has a wide and fast microbiological efficacy, but is not compatible with certain plastics or metals, especially regarding brass and chromium plating. Pitting corrosion, among others, is possible in several stainless steel grades. Using a harmonised 2-component formulation has made it possible to guarantee a very comprehensive effect spectrum with an extraordinarily good and practice-oriented compatibility of materials. terralin® PAA component base contains an active, stabilised, balanced peracetic acid. In addition to an alkaline component to adjust the pH value, the component additive provides phosphates and other anti-corrosion components. During the production of the stock solution by dilution with water and simultaneous mixing of the two components, an almost neutral, buffered application solution with a pH value of approx. 6 is obtained. Ensure complete wetting of the surfaces. Ensure that all visible dirt is removed before disinfection. After completing the work, dispose of the working solution and clean the equipment thoroughly with water. For professional use only. Any serious incidents related to the product are to be reported to the manufacturer and competent authority. Not for final disinfection of semicritical and critical medical devices!

Information for order

ItemDelivery formItem no.
terralin® PAA 160 ml (2x80 ml)12/Cartonon request
These products are not available in every country. For more information please contact our local subsidiary or distributor.

Environmental information

schülke manufactures products economically and with advanced, safe and environmentally friendly production processes while at the same time maintaining our high quality standards.
EuroNormCE 0297
Manufacturer:
Bioxal SA
Route des Varennes - Secteur A
BP3007271103 Chalon-sur-Saône
France

Privacy Policy

We use analysis methods (e. g. cookies) to measure how often our site is visited and how it is used.
We embed third-party content from other providers (e. g. videos) on our site. We have no influence on further data processing and any tracking by the third party provider.
In this context, we also use service providers in third countries outside the EU that do not have an adequate level of data protection, which harbors the following risks: Access by authorities without informing the data subject, no data subject rights, no legal remedies, loss of control.
With your settings you consent to the processes described above. You can revoke your consent with effect for the future. You can find more information in our privacy policy.